ÇEVRE TEKNOLOJİSİ İLE İLGİLİ OLARAK  YAPILAN ÇALIŞMALAR

 

Removal of fallout radionuclides from water.

U. ÖZER

Fen Edebiyat Fakültesi Kimya Bölümü

Atom Praxis 6: 222-223, 1963.

The experimental results indicate that water containing fission products could be decontaminated fairly successfully by simply filtering through a layer of soil, sand, activated carbon or suitable mixtures of these. Soil and sand, however, seem to be most suitable for the purpose, because their capacity to extract radioactive species increases markedly with thickness. We believe this filtration method followed by poling could be a practical way to recondition water for people in areas where water contamination exceeds the maximum permissible concentration. The removal of radioactive substances from water by soil and other media might be due to two main processes acting together: Adsorption and/or absorption; ion exchange. Work will be continued to determine the extent and mechanism of removal for individual radionuclides, such as.

 

Calcium silicates as lime substitute.

 V. PINARLI, G.M. SAUL

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Water Science and Technology, 28(1):257-261, 1993

An experimental study has been carried out of the removal of iron from solutions of ferric chloride by lime, b-dicalcium silicate (C2S) and a-monocalcium silicate (CS) and of the treatment of the resulting sludge. C2S promoted the flocculation of iron precipitates to achieve higher settling, thickening and dewatering rates. The effect of first minute settling time is especially evident that 60% and 22% of the iron respectively was removed when 0.39 g/l of C2S and 0.21 g/l of lime were applied to solutions containing 100 mg/l  Fe 3+ . 99% and 48% of the iron respectively was removed in the first two minutes of settling period when 3.90 g/l of C2S and 2.10 g/l of lime were applied to solutions containing 1000 mg/l  Fe 3+. Zone settling and thickening of the iron flocs below a sludge blanket formed were observed and zone settling velocities were determined as 4.6 and 3.7 cm/minute for C2S and lime respectively. When C2S was used as precipitant for different iron concentrations i.e. 10, 1000, 1000 mg/l Fe 3+, the sludge produced had lower specific resistance to filtration (5.38 x10 12, 1.75x10 12, 1.13 x 10 12 m/kg) than that  (6.77 x10 12, 5.76 x10 12, 3.98 x 10 12 m/kg) when lime was used, respectively. C2S treatment significantly increased the filter yield hence reduced the size of the dewatering plant.

 

Constructive sludge management reutilization of municipal sewage sludge in Portland cement mortars.

V. PINARLI, N.K. EMRE

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Environmental Technology 15(9):833-852, 1994

Sludge produced by the treatment of municipal sewage wastes are becoming increasingly difficult to dispose of because the quantity of sludge is increasing due to an increase in population and sewered areas. Many sludge disposal alternatives such as agricultural use, landfilling marine disposal and incineration, etc, have adverse environmental impacts. There is a resulting increase of interest in reuse of sludge by incorporation into construction materials. In the present study, properties of digested, dewatered, dried and pulverised sludge blended Portland cement mortars are investigated. Sludge was used as replacement for 1, 2, 5, 10, 20, 30 and 40 percent by weight of the cement. The results indicate that initial and final setting times are longer with an increase of sludge. The mortar samples cast in standard moulds were cured for periods of 3, 7, 14 and 28 days before testing for compressive and tensile strength. The addition of 40 percent sludge caused the initial and final setting times of mortar to increase about 19 fold and 35 fold compared to control mortar with a water to cement ratio of 0.5. The effects of pulverised sludge on the Le Chatelier expansion and specific surface area of mortar are not significant. The addition of sludge adversely affected the compressive and tensile strength development. For 5 percent replacement of cement by pulverised sludge, the compressive and tensile strengths reduced by 32 and 38 percent respectively.

 

An innovative sludge disposal option reuse of sludge ash by incorporation in construction materials.

V. PINARLI, G. KAYMAL

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Environmental Technology 15(9):843-852, 1994

Sludge production is an unavoidable consequence of wastewater treatment and creates problems for disposal. For highly urbanised cities, incineration of sludge might be a viable solution for sludge disposal. Incineration of digested and dewatered sludge, yields an odourless, cellular, porous mass of sludge ash with low unit weight. In the present study, a comprehensive test programme was developed to examine the potential for using pulverised sludge ash as a cement substitute in mortar. Sludge ash used as replacement for 5, 10, 15 and 20 percent by weight of the cement. The results show that initial and final setting times are longer with an increase of pulverised sludge ash. Effects of pulverised sludge ash on the  Le Chatelier expansion and specific surface area of mortar are not significant. The test samples cast were cured for periods of 3, 7, 14 and 28 days before testing for compressive and tensile strength. The strengths for the mortars at different ages decrease with the increase of sludge ash. However, with 10 percent replacement of cement by sludge ash, the 28 th day compressive and tensile strength for the mortars are similar to conventional mortar.

 

Atık su arıtım çamuru külünün beton malzemesi olarak kullanımı.

 V. PINARLI, B.O. AKAY

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

İstanbul Teknik Üniversitesi 4. Endüstriyel Kirlenme Sempozyumu Kitabı. İstanbul, Eylül 1994:243-256.

 Kentsel atık su arıtım tesisleri, kömüre dayalı termik santraller, demir çelik, bakır, ferrokrom, gübre, kağıt v.b. sanayi dallarından önemli miktarlarda ve tiplerde çamur, çamur külü, uçucu kül, yüksek fırın cürufu gibi atık malzemeler ortaya çıkmaktadır. Bunların inşaat sektöründe ilave ya da ikame malzeme olarak ya da kendi başına kullanılması suretiyle bir taraftan sınırlı doğal kaynakların hızlı tüketimi önlenirken, diğer taraftan atıkların neden olduğu çevre problemlerine de bir ölçüde çözüm getirilmiş olacaktır. Laboratuarda gerçekleştirilen deneysel çalışmada kentsel atık su arıtma çamurlarının yakılmasıyla elde edilen ve uzaklaştırılması gereken çamur külünün çeşitli oranlarda çimento yerine kullanılmasıyla hazırlanan betonların çeşitli özellikleri, katkısız şahit betonla karşılaştırılmalı olarak incelenmiştir.

Beton karışımlarındaki çimentonun ağırlığı % 0, % 5, % 10, % 15 ve % 20 oranlarında azaltılarak yerine bu oranlarda azaltılan çimento ağırlığı kadar öğütülmüş çamur külü kullanılmıştır. Betonun priz süreleri penetrasyon direnci metoduyla tayin edilmiştir. Çamur külü kullanılmasıyla priz başlangıcı ve priz sonu sürelerinin uzadığı görülmüştür. Beton numuneleri 3, 7, 14 ve 28 gün küre tabi tutulduktan sonra basınç mukavemetleri ölçülmüştür. % 5 oranında çamur külü kullanılan betonun basınç mukavemetinin her yaşta şahit betondan daha yüksek olduğu görülmüştür. % 10 oranında kül içeren betonların 28 günlük basınç mukavemetleri şahit betona yakın bulunmuştur. % 20 oranında çamur külü kullanıldığında dahi 28 günlük basınç mukavemeti şahit beton mukavemetinin % 94 ünün üzerindedir. Çamur külü kullanıldığında betonlarda su absorpsiyonu ve permeabilite katsayısının azaldığı görülmüştür.

 

Clinker minerals in waste water treatment and their effect on sludge thickening, dewatering, disposal.

 V. PINARLI, H. GÜNDOĞAR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Brunel University, United Kingdom & Dumlupınar University, Kütahya, Turkey. Proceedings of the First International Symposium on Mine Environmental Engineering. 29-31 July, 1996: 172-178

Chemical treatment of municipal wastewater is frequently used in several parts of the world, either as the only treatment or as pretreatment ahead of biological treatment. Since a major part of the contaminants in wastewater is associated with particles ( organic matter, suspended solids, bacteria, heavy metals  etc. ) or may be precipitiated ( phosphates and metals ) substantial removals of those contaminants may be achieved with chemical treatment alone. An experimental investigation was carried out of the treatment of sewage effluent by using finely ground cement clinker as an alternative coagulant (aid) to hydrated lime, alone or together with the costly traditional coagulant such as Fe (III) salt (i.e. ferric chloride). Higher removal efficiencies were achieved when the clinker or hydrated lime was used together with the iron coagulant. Floc settling velocities and therefore corresponding surface loading rates were increased as well as sludge specific resistance to filtration values were decreased, the sludge was dewatered to a higher cake solid concentration thus the size of the treatment plant required, the cost of sewage treatment and sludge disposal should be less with clinker utilisation instead of lime in this field of effluent treatment.

 

Biological treatment of saline wastewater in an percolator unit utilizing halophilic bacteria.

F. KARGI, A. UYGAR

Environmental Technology ,17:325-330, 1996.

 

Tuz içeren atık suların sürekli biyodisk ünitesinde arıtımı.

F. KARGI, A. UYGAR, R.A. DİNÇER

İTÜ V. Endüstriyel Kirlenme Sempozyumu. İstanbul. 1996.

 

An Exploration of the removal of iron from solution using b dicalcium silicate and a monocalcium silicate as alternative precipitants to calcium hydroxide.

V. PINARLI

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Environmental Technology, 17(10):1071-1081, 1996.

The present work has studied the removal of iron (Fe ³+) ions from solution using b- dicalcium silicate (C2S) a-monocalcium silicate (CS) and calcium hydroxide. The merits of these precipitants were analysed by studying their effectiveness for removing iron (Fe ³+) from solutions of ferric chloride and the properties of the flocs formed. The initial concentration of iron in solution  was varied between 10 and 1000 mg  l ˉ¹ Fe ³+ for different additions of precipitant. The residual silicate particles upon hydrolysis appear to enhance the overall removal process in a manner different from the coagulating effect of calcium ions. Considerable enhancement in the rate of removal of iron resulted from use of more finely ground silicates. It is suggested that the reaction can proceed either by the specific adsorption of polynuclear ferric hydroxo complexes on to surface of negatively charged silica rich layers of  C2S formed by loss of Ca 2+ upon hydrolysis or by direct exchange of Fe ³+ with Ca 2+ in the charged layer. At the end of the second minutes of the settling period remaining iron concentrations were 12.0 mg  l ˉ¹ and 525.0 mg  l ˉ¹, respectively when 3.90 g  l ˉ¹  of C2S and 2.10 g  l ˉ of calcium hydroxide were applied to solutions containing 1000 mg  l ˉ¹ Fe ³+ . By the end of second minutes of settling period the remaining  iron concentrations were 40 mg  l ˉ¹ and 78 mg  l ˉ¹, respectively when 0.39 g  l ˉ¹ of C2S and 0.21 g  l ˉ¹ of calcium hydroxide were applied to solutions containing 100 mg  l ˉ¹ Fe ³+  in a sedimentation tank designed on the basis of surface loading rate of 48 m3m -2d -1. In the case of C2S the specific resistance to filtration and the Capillary Suction Time (CST) values of the sludge produced were lower than that when calcium hydroxide was used thus indicating better dewaterability characteristics. The filter yields of the sludge from C2S and calcium hydroxide treatment of 10, 100 and 1000 mg  l ˉ¹ iron solutions were estimated as 27.0, 15.8, 23.2 kg m-3h-1 and 12.8, 6.5, 7.8 kg m-3h-1 respectively.

 

Katı atık depo gazlarında bulunan karbondioksit ve metan arasındaki ilişkinin belirlenmesi.

 F. PAYAN, İ.D. KARGI

Dokuz Eylül Üniversitesi ve Çanakkale Belediyesi Yerleşim ve Çevre Sorunları Çanakkale ili Sempozyumu. Çanakkale. Eylül 1996.

 

Düşük F/M oranında organik madde gideriminin belirlenmesi.

S. K. AKAL, H. S. BAŞKAYA, T.YONAR

Mühendislik Mimarlık Fakültesi, Çevre Mühendisliği Bölümü

24-26 Haziran 1996 tarihinde Bursa’da yapılan I. Uludağ Çevre Mühendisliği Sempozyumunda bildiri olarak sunulmuştur.

I. Uludağ Çevre Mühendisliği Sempozyumu Kitabı. Bursa. Uludağ Üniversitesi Basımevi, 1997:277-282

Bu yazıda aktif çamur sisteminde aerobik ortamda düşük F/M oranındaki kesikli reaktör üzerinde inceleme ve çalışmalar yapılmıştır. Elde edilen veriler yardımıyla glikozun KOİ ve AKM değerlerinin zamanla değişimi belirlenmiştir.

 

Marmara bölgesinde rüzgar enerjisinin durumu, model bir rüzgar türbin tasarımı ve imalatı.

İ.KARAGÖZ, A. AYDIN, M. KIRBIYIK

Mühendislik Mimarlık Fakültesi Makine Mühendisliği Bölümü

24-26 Haziran 1996 tarihinde Bursa’da yapılan I. Uludağ Çevre Mühendisliği Sempozyumunda bildiri olarak sunulmuştur.

I. Uludağ Çevre Mühendisliği Sempozyumu Kitabı. Bursa. Uludağ Üniversitesi Basımevi, 1997:605-614

Enerji ihtiyacının artması ve çevre kirliliğinin önem kazanması rüzgar enerjisinden en iyi şekilde yararlanmak için yapılan çalışmaları hızlandırmıştır. Türkiye rüzgar enerjisinden yararlanabilecek bir ülke olup, meteorolojik veriler Marmara Bölgesi'nin bu bakımdan en zengin bölge olduğunu göstermiştir. Rüzgar enerjisini değerlendirmek için kullanılan yatay eksenli rüzgar tribünlerinin performansını etkileyen parametrelerin incelenmesi ve optimum değerlerin belirlenmesi için üzerinde çeşitli deneylerin yapılabileceği, laboratuar tipi model türbinin tasarım ve imalat aşamaları verilerek maliyet analizi ve ekonomiye katkısı tartışılmıştır.

 

The use of multiple tube sampling to device a protocol for identifying unknown volatile organic compounds in the workplace atmospheres.

N. KILIÇ

I. Kızılırmak Fen Bilimleri Sempozyumu kitabı. Kırıkkale . Mayıs 1997:4

In this study multiple adsorbent tube sampling has been applied to determine the composition of an unknown mixture of compounds present in a laboratory atmosphere. This procedure was devised as a preliminary investigation as a part of a strategy for air monitoring prior to the quantitative analysis. The adsorbents used in this study are Tenax TA (weak), Chromosorb 106 (medium) and Carbosieve III (strong). Sampling of the laboratory air was performed by the active (pumped) sampling method using apparatus which allows the use of multiple adsorbent tubes. By this sampling procedure a wide volatility range of unknown organic compounds could be sampled and determined.

 

Atmosferde kanser yapıcı uçucu bileşiklerin kontrolü.

N. KILIÇ

Türkiye’de Çevre Kirlenmesi Öncelikleri Sempozyumu II. Gebze. Mayıs 1997:433.

Atmosferde bulunan ve elementel karbon, karbondioksit ve karbon monoksit dışındaki karbonlu bileşikler olarak tanımlanan uçucu organik bileşikler (UOB) hava kirleticilerin önemli bir sınıfını oluştururlar. Uçucu organik bileşiklerin çoğunun fotokimyasal duman oluşumunu başlatmak ve bazılarının da ozon tabakasının incelmesine neden olarak global ısınmaya katkıda bulunmak gibi insan sağlığına dolaylı etkilerinin yanı sıra kansere yol açma gibi doğrudan etkileri vardır. Özellikle benzen gibi mono aromatik (MAH) ve pek çok poli aromatik hidrokarbonların (PAH) kanser yapıcı özellikleri nedeniyle sınır değerlerinin düşürülmesi için çalışmalar yapılmaktadır. Atmosferde bulunan uçucu organik bileşiklerin kontrolü için yaygın olarak kullanılan yöntem bu bileşiklerin aktif karbon ya da Tenax gibi katı adsorbentler üzerine adsorblanarak tutulması ve tutulan bileşiklerin termal desorpsiyon ile kapiller kolona gönderilerek ayrılmasından sonra alev iyonlaşma veya kütle spektrometresi dedektörlü gaz kromatografisi ile analiz edilmesidir.

 

Effect of liquid phase aeration on performance of rotating biodisc contactor treating saline wastewater.

 F. KARGI, A. UYGUR

Environmental Technology, 18:623-630, 1997.

 

Biological treatment of saline wastewater in a rotating biodisc contactor by using holophilic organisms bioprocess.

F. KARGI, A. UYGUR

Engineering 17: 81-85, 1997.

 

Atıksulardan Ni (II), Zn (II) VE Cu (II) iyonlarının uçucu kül, çimento baca tozu ve klinoptilolit ile giderimi.

V. PINARLI, S. ÇAKIR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Türkiye'de Çevre Kirlenmesi Öncelikleri Sempozyumu II. Gebze, 22-23 Mayıs, 1997.

 

Akışkan yataklı biyolojik reaktörlerde azot giderimi.

F. KARGI, A. UYGUR

İstanbul Teknik Üniversitesi 6. Endüstriyel Kirlenme Sempozyumu, İstanbul, 1998.

 

Influence of aerobic selector technology for heavy metal removal by activated sludge.

Y. TAŞDEMİR, D. CHA

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

TUBİTAK ,SECOTOX 98 Sempozyumu Kitabı, Antalya,  19-21 Ekim, 1998.

 

Aktif çamur proseslerinde şişkin çamur oluşumunun aerobik seçicilerle önlenmesi.

Y. TAŞDEMİR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Uludağ Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 1998.

 

Measurement of dry deposition and air-water exchange of polycyclic aromatic hydrocarbons (PAHs) with the water surface sampler.

M. ODABAŞI, Y. TAŞDEMİR, N. VARDAR, A. SOFUOĞLU, T.M. HOLSEN

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Environmental Science and Technology, 1998.

 

Atık suların biyolojik olarak arıtılmasında mekanistik bir model yaklaşımı.

S.K. AKAL, V. PINARLI, T. YONAR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Erciyeş Üniversitesi Teknoloji Araştırma ve Uygulama Merkezi, Kayseri I. Atık Su Sempozyumu Kitabı. Kayseri, 22-26 Haziran , 1998

Atık su arıtımında önemli bir yer teşkil eden biyolojik arıtma sistemlerinin tasarımı, model kullanımını gerektirir. Uygun sistemlerin oluşturulması veya belirlenen tasarım alternatiflerinin çeşitli işletme koşullarındaki muhtemel davranışlarının irdelenmesi matematik modeller yardımıyla gerçekleştirilir. Bu amaçla kullanılan matematik model, laboratuar ölçekli reaktörler veya pilot tesisler gibi fiziksel modellerle yapılan çalışmalardan elde edilen sonuçların istatistik değerlendirmeleri ile elde edilmiş ampirik bir model olabileceği gibi sistemde meyadana gelen belli başlı olaylarla ilgili teorik bilgilerden hareketle kurulmuş mekanistik bir model de olabilir. Bu çalışmada atık suların arıtılmasında kullanılan biyolojik arıtma ünitelerinden aktif çamur sistemlerinde ürün oluşumu üzerine kurulmuş mekanistik bir model yaklaşımı yardımıyla atık sularda mevcut organik maddelerin konsantrasyonlarında meyadana gelen değişimler belirlenmiştir. Elde edilen değişimler grafik halinde gösterilerek sonuçlar özetlenmiştir.

 

Aktif çamur sisteminde substrat giderimi.

S.K. AKAL, V. PINARLI, H.S. BAŞKAYA, T. YONAR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Uludağ Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 1999.

Bu makalede biyolojik arıtma sistemlerinden özellikle aktif çamur proseslerinin tasarımı ve işletilmelerinde substrat giderim mekanizmasının önemle göz önüne alınması gerektiği belirtilmiştir. Bu amaçla substrat giderimi konusunda genel bilgiler verilmiş, literatürde mevcut eşitlik ve ifadeler açıklanarak bu konuda yapılan çalışmalar değerlendirilmiştir.  

 

Deponi Gazının Elektrik Üretiminde Değerlendirilmesinde Proje Aşamaları

SALİHOĞLU,  N.K,   PINARLI,  V.,   ÇELİK, G., , 

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü  

      Ulusal Katı Atık Kongresi – UKAK 2001, Dokuz Eylül Üniversitesi  ÇevreMühendisliğiBölümü ve Çevre Araştırma Ve Uygulama Merkezi, Bildiriler Kitabı, “Çöp Depolama Alanlarının Çevresel Etkileri ve İşletimi” Oturumu, 17-28, İzmir, 18-21Nisan 2001.

  Katı atık depolama sahalarından çıkan deponi gazının içeriğinde bulunan metan (CH4), enerji eldesinde önemli bir kaynaktır. Deponi gazının geri kazanımı için geliştirilen birçok teknoloji dünyada pek çok yerde yaygın bir şekilde kullanılmaktadır ve uygun saha koşullarında ekonomik olarak uygulanabilir olduğu bilinmektedir. Türkiye’de bu alandaki ilk uygulama, Bursa Demirtaş Depolama Sahasında Metan Gazından Elektrik Enerjisi Eldesi projesidir. Kasım 1998’de enerji üretimine başlayan tesis yaklaşık %30 kapasiteyle çalışmaktadır. Bu çalışmada, deponi gazının değerlendirilmesiyle ilgili proje kriterleri ele alınmış, dünyadaki örnekler ışığında Bursa örneği, projelendirme aşamasından mevcut elektrik üretim aşamasına kadar incelenmiştir.

 

Katı Atık Depolama Sahalarında Oluşan Metandan Elektrik Enerjisi Üretimi ve Bursa Örneği

V. PINARLI, N.K. SALİHOĞLU, T. YONAR, G. ÇELİK 

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

      Birinci  Ulusal Çevre Kirliliği Kontrolü Sempozyumu, ODTÜ- Çevre Mühendisliği Bölümü,Thames Water, TÜBİTAK, Bildiriler Kitabı, 367-370,  Ankara, 4-6 Ekim 2000

Katı atık depolama sahaları, organik maddenin parçalanması sırasında oluşan  depolama sahası gazının (LFG) yapısından dolayı vahim çevresel etkilere sebep olabilmektedir. Bu yüzden depolama sahası gazının kontrolü ve kullanımı depolama sahası gazının etkilerinin azaltılması için önemli hale gelmiştir. Bu yazıda depolama sahası gazı oluşumu ve depolama sahası gazından elektrik enerjisi üretim kapasitesinin değerlendirilmesi için enerji üretim tesisleri incelenmiştir. Aynı zamanda Türkiye’deki ilk depolama sahası gazından enerji üretim tesisi örneği olan Bursa Demirtaş eski depolama sahasındaki metan içeriği ve elektrik üretim oranları incelenmiştir.

 

Sustainable Waste Management-Studies on the Use of Sewage Sludge Ash in the Construction Industry as Concrete Material

V.  PINARLI

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

In Ravindra K Dhir, Tom D. Dyer and    Kevin A. Paine (Editors): Sustainable Construction: Use of Incinerator Ash, pp. 415-426, Thomas Telford Books Publishing, London, Great Britain, 2000, ISBN: 0 7277 2861 X

The opportunities for developing sustainable use of materials are becoming increasingly advantageous and the recovery of maximum value from waste materials is a key concern in this process. One of the most effective approaches to value recovery is through the generation of heat and power from waste incineration. Whilst the benefits of this approach are significant, disposal of the ash is the main difficulty to justifying incineration as a wholly sustainable solution. The construction industry  can offer a number of potential applications for using incinerator ash. Such opportunities offer means of maximizing the value of these wastes and allowing them to be regarded as a useful resource. A substantial amount of waste materials such as sludge, sludge ash, fly ash, blast furnace slag etc. are produced from municipal waste water treatment plants, coal-fired thermal power plants, iron and steel, copper, ferrochrome, pulp and paper industries etc. In this experimental study carried out in the laboratory, sludge ash obtained from the incineration of municipal waste water treatment sludges were utilized in concrete production as cement substitute in varying proportions.0,5,10,15 and 20 percent of cement by weight in concrete mixture were substituted by the pulvirized sludge ash. Initial and final settling times of the concrete were longer with higher percentages of sludge ash used. With 5% replacement of cement by pulvirized sludge ash, the compressive strengths at all ages were higher than the control samples. With 10% replacement of cement by sludge ash, the compressive strength at different ages were about the same as the reference cubes. The water absorption and permeability of concrete with sludge ash decreased. 

Feasibility  studies  and conceptual design  of common  effluent  treatment  system  for  tanneries  in  Bursa   leather organized industrial estate

V.PINARLI, S. K.   AKAL, H. S.   BAŞKAYA

  Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Fourth International Symposium on Waste Management  Problems in Agro-Industries 23-25 September, 1998, İstanbul

 

Upgradig Operation of the Wastewater  Treatment  Plant of a  Pulp  and  Paper  Industry

V. PINARLI, S. K.     AKAL, T.  YONAR

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

SECOTOX 98 Sempozyumu,  TÜBİTAK,1998 19.-21 October 1998

Deponi Gazının Elektrik Üretiminde Değerlendirilmesinde Proje Aşamaları
N. K. SALİHOĞLU, V.  PINARLI, G.  ÇELİK

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

1.Ulusal Katı Atık Kongresi – UKAK 2001, Dokuz Eylül Üniversitesi - Çevre Mühendisliği Bölümü ve Çevre Araştırma Ve Uygulama Merkezi, Bildiriler Kitabı, “Çöp Depolama Alanlarının Çevresel Etkileri ve İşletimi” Oturumu, 17-28, İzmir, 18-21 Nisan 2001.

Katı Atık Depolama Sahalarında Oluşan Metandan Elektrik Enerjisi Üretimi ve Bursa Örneği

V.PINARLI, N.K. SALİHOĞLU, T. YONAR, G. ÇELİK

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

1.Ulusal Çevre Kirliliği Kontrolü Sempozyumu, ODTÜ- Çevre Mühendisliği Bölümü, Thames Water, TÜBİTAK, Bildiriler Kitabı, 367-370, Ankara, 4-6 Ekim 2000 .

Sustainable Waste Management-Studies on the Use of Sewage Sludge Ash in the Construction Industry as Concrete Material

V. PINARLI

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

 In Ravindra K Dhir, Tom D. Dyer and    Kevin A. Paine (Editors): Sustainable Construction: Use of Incinerator Ash, pp. 415-426, Thomas Telford Books Publishing, London, Great Britain, 2000, ISBN: 0 7277 2861 X

Endüstriyel Atıksu Arıtma Tesisi Boyutlandırma Kriterleri

K. KESTİOĞLU

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

 Uludağ Üniversitesi., Müh.-Mimarlık Fak. Çevre. Müh. Böl Bursa, 2001.Ders Kitabı  olarak VİPAŞ  tarafından yayınlanmıştır. ( ISBN-975-564-114-9 )

 

Atıksu Arıtımında Biyokimyasal Prosesler

K. KESTİOĞLU

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Uludağ Üniversitesi., Müh-Mimarlık Fak. Çevre Müh. Böl. Bursa,2001. Ders Kitabı olarak VİPAŞ tarafından yayınlanmıştır. ( ISBN-975-565-110-6 )

 

Tıbbi Atıkların Toplanması, Taşınması ve Bertarafında Karşılaşılan Sorunlar - Bursa Örneği

N. SALİHOĞLU, V. PINARLI, G. SALİHOĞLU

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

 IV. Ulusal Çevre Mühendisliği Kongresi, 07 - 10 Kasım 2001, İçel.

 

The Effect of Alkaline Stabilised Sludge Applicatıon on the Microbiological Quality of Soil and Leachate. 

Kocaer, F. O., Alkan, U., Başkaya, H.S.

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Journal of Plant Nutrition and Soil Science.167:704-712, 2004

 

Feasibility of physico-chemical treatment and Advanced Oxidation Process (AOPs) as a means of pretreatment of olive mill effluent (OME)

Kestioğlu,K., Yonar, T. ; Azbar, N.

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Process Biochemistry. 40: 2409-2416, 2005.   

 

Stabilization and Solidification of Waste Phosphate Sludge Using Portland Cement and Fly Ash as Cement Substitute.

Pinarli, V., Karaca, G., Salihoglu, G., Salihoglu, N.K.

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Journal of Environmental Science and Health, Part A., 40(9):1763-1774, 2005.

 

Multicomponent activated sludge model for reactors in series with recycling . 

Ciner F, San HA, Sarioglu M, Solmaz S.K.A. 

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

INTERNATIONAL JOURNAL OF ENVIRONMENT AND POLLUTION, 23 (4): 397-408, 2005.

 

Decolorisation of textile effluent using homogeneous photochemical oxidation processes .  

T. YONAR, G.K. YONAR, K. KESTIOĞLU, N. AZBAR ,   

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

COLORATION TECHNOLOGY, 121 (5): 258-264 , 2005.

 

Colour and COD removal from textile effluents by coagulation and advanced oxidation processes . 

Akal Solmaz,S.K., A. Birgül,G.E. Üstün, T. Yonar.  

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Coloration Technology.122:102 - 109, 2006.

 

Properties of steel foundry electric arc furnace dust  solidified / stabilized with portland cement. 

Salihoglu G., Pinarli, V., Salihoglu, N.K. Karaca, G.

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Journal of Environmental Management, 2007.

 

Effect of Sludge Age on Heavy Metal Biosorption by Selector Activated Sludge.  

ALKan,U.,  S. Çalışkan Eleren.  

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

International Journal of Environment and Pollution. 2007.    

 

Solar Drying in Sludge Management in Turkey.

SALİHOĞLU, N.K.,  PINARLI, V., SALİHOĞLU, G. 

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Renewable Energy, 2007.

 

Adaptive Neuro-Fuzzy Inference Technique for Estimation of Light Penetration in  Reservoirs’. 

Soyupak,S., Karaer,F., Hekim,H., Şentürk,E., Kılıç,H.  

Mühendislik Mimarlık Fakültesi Çevre Mühendisliği Bölümü

Limnology, 8/2,200

 

yayınlar sayfası